Kitchen Sink Faucet

Product classification

1.According to the installation mode, it can be divided into desktop type and wall-mounted type.

2.It can be divided into residential use and public use.

3.According to the material, it can be divided into ceramic sink, FRP sink, stainless steel sink, steel plate enamel sink and artificial stone sink.

technical requirement

1.Overflow function

2.Duty tolerance

The washing tank should be able to withstand the load of 0.44 kN.

Installation method

Step 1: Mark’s position and ability to groove in the wall

The position of the sink should accurately indicate the help of the pencil used. The position of the sink should be marked with the help of an accurate pencil. Please chase the top edge of the receiver on the wall so that the sink of the jigsaw blade under the table and the top edge are carefully grooved. Make the carving on the wall, the top edge of the sink, and make the top edge of the sink carefully under the blade of the slot table saw curve machine.

Step 2: Dig holes in the wall to fix the bracket

Please have 2 holes at the bottom of the fixing bracket flume beside the wall. The brackets for repairing the flume near the surface of the bottom walls of the two holes. These holes shall be 225 mm centered from either side 300 mm in case of sinking in 750 mm and 600 mm lengths. These holes should sink 750 mm and 225 mm from the center to both sides to prevent 600 mm from sinking. CI cantilever bracket should be embedded in cement concrete with a ratio of 1:2:4 and a size of 100*75*150 mm. CI cantilever bracket should be embedded in cement concrete block size ratio of 1:2:4 in 100 *75 *150 mm. The two parentheses should be in one level and one line. The two brackets should be at one level and one line. The CI cantilever bracket should be embedded in the front skirt/tiles has been completed. The CI cantilever bracket should be embedded in the wall brick skirt/work is done. Insert the test sink into the hole above the counter to keep fit. Insert the sink hole to test the fitness of the top cabinet. After testing fittings, flume and adjustment holes are taken out, if necessary. After testing, remove sinking and fittings, adjust holes, if necessary.

Step 3: Repair the sink at an appropriate level

At the top of the kitchen sink, the kitchen level should be centimetre high on the 80th to 82nd floors. The top of the kitchen sink should be 80 to 82 centimeters high from the floor level of the kitchen. The following flume tape should be at 40 cm high level on the kitchen floor. Recording below sink should be 40 cm high level kitchen floor.

Step 4: Will sink in the right space

Measure the space and place in the upper left corner of the sink counter to sink to the correct size according to the existing hole. Measure the space away from the counter and sink to the correct size at the top of the sink and place it on the top side of the counter from the upper left corner of the space sink and keep the sink 2 cm thick equal to the stone thickness at the top of the countertop below the counter. Use stones that fall on the ground from the top side of the counter and maintain the highest sink or equal to 2 centimeters thick below the top level of the counter.

Step 5: Keep the sink table parallel

The way to ensure that the sink countertops are parallel is to keep them in the bottom cabinet without disturbing them. Make sure that the sinks are parallel and on a table without disturbing the potential cabinet.

Step 6: Install sink correctly

Suitable for sink drain holes with lead white and threads “per manufacturer’s instruction CP brass or C by C union. P. Brass or PV fits CC Alliance in tank drain holes according to manufacturer’s instructions with white lead and line to ensure fit without any leakage tightness. Make sure that there is no leakage in the assembly. CP brass or PVC trade union shall be connected to 40 mm GI or C-by-C waste water pipe, CC PV P. Brass or trade unions should be connected to 40mm or P. V. I C sewer, this is the discharge of the wall bent into a floor trap. It’s a trap for walls and bending out of the floor.

Step 7: Apply for chasing and sealing slots

Whether sealants are used in chasing and grove parts or stationary sheets of white cement paste. Sealant or white can also be used in catch-up and forest cement fixed part of the tank. Immediately after insertion, the sealant or white cement paste becomes hard before applying for cave sinking. It becomes difficult to insert into the sinking hole immediately before applying cement sealant or white. Repair the sink carefully and press it under the seal. Repair the sink carefully and press the seal. Remove excess sealant or white cement paste carefully. Remove excess sealant or white cement paste carefully.

Step 8: Clean properly and apply polishing wax

Clean sinks, pipes with clean cloth leave any traces on the sinks and countertops and countertops. Clean sinks, pipes, with clean cloth table without leaving traces, the table sinks. Use their wax to polish. Use polishing wax.

Step 9: Watch out for drainage panels

The drainage board should stay in the sink at the end and support the drainage board at the other end of CI. The drainage board at the other end should rest and sink. The CI brackets should be embedded into the concrete blocks of 1:2:4 size 100x75x150mm. The size of cement concrete block embedded in brackets is 100 x 75 x 150 mm 1:2:4. Drainage panels should be placed in such a way that water must be drained directly into the tank. Drainage panels should be placed directly in such a pool where water must be sucked. Make sure that the installed sink does not disturb the support of the existing cabinets and countertops. Ensure that after installation, we will have cabinets and support countertops for our own sinks.

Step 10: Install faucets

To install the faucet, the catchment tank is poured on the table. Install the faucet and set it upside down on the table. Correction of supply pipes and tail plates through sealing washers and sink faucets. Repair the supply pipe and tail block of the faucet through the faucet and sink of the sealed gasket. Tighten the nuts and washers under the sink deck. Fastening nuts and lower deck of Wallace sink. By tightening the nuts to ensure that the faucet can swing fully and repair the surrounding flume, create a flume and a silicone filling bead on the entire periphery of the waterproof seal bottom of the mesa. Tighten the nut to ensure that the faucet can swing and repair a series of silicon fillings around the entire perimeter to create a stable sink between the sink and countertop seamless seal.